Maytag Washer F8E6 Water Hazard Error

The Maytag washer F8E6 error code can have different meanings depending on the washer model.

On some Maytag top-load washers, F8E6 indicates a water hazard condition. This can occur when the washer detects water in the tub while the lid has remained open for an extended period.

On other models, F8E6 may indicate that hot water was not detected or that the hot and cold water inlet hoses are connected incorrectly.

Because the meaning varies by model, check your washer’s model number and consult its owner’s manual before beginning troubleshooting.

Common Causes of the Maytag F8E6 Error

Several issues can trigger the F8E6 error code, including:

  • Hot and cold inlet hoses reversed
  • Incorrect hose installation
  • Water supply valves not fully open
  • Restricted water flow
  • Kinked water inlet hosesCommon Causes of the Maytag F8E6 Error
  • The possible causes of an F8E6 error depend on the Maytag washer model.
  • Water Hazard or Lid-Related Causes
  • On models where F8E6 indicates a water hazard condition, possible causes include:
  • The washer lid remaining open for an extended period while water is in the tub.
  • The lid being left open during a soak cycle.
  • A lid that does not close properly.
  • A faulty lid switch or lid lock that prevents the washer from detecting a closed lid.
  • Water Supply-Related Causes
  • On models where F8E6 indicates a hot water detection or supply problem, possible causes include:
  • Hot and cold inlet hoses connected to the wrong ports.
  • The hot water supply valve being closed.
  • Restricted water flow through the inlet hoses.
  • Kinked or pinched water inlet hoses.
  • Clogged inlet filter screens.
  • A malfunctioning water inlet valve.
  • Important: Not every cause applies to every Maytag washer. Check your washer’s model-specific documentation to determine which troubleshooting steps are appropriate.
  • Faulty water inlet valve
  • Wiring or sensor problems

How To Fix Maytag Washer F8E6 Error

Follow these troubleshooting steps to help diagnose and fix the F8E6 error code.

1. Disconnect Power

Unplug the washer from the electrical outlet before beginning any inspection.

2. Check the Water Hose Connections

Inspect the water inlet hoses at the back of the washer.

Make sure:

  • the hot water hose is connected to the hot inlet
  • the cold water hose is connected to the cold inlet

Reversed hoses are one of the most common causes of the F8E6 error.

3. Verify Water Supply Valves

Make sure both hot and cold water supply valves are fully open.

Many Whirlpool washers require both water supplies to operate correctly.

4. Inspect the Inlet Hoses

Check the hoses for:

  • kinks
  • bends
  • pinched sections
  • leaks

Straighten or replace damaged hoses if necessary.

5. Clean the Inlet Filter Screens

Turn off the water supply and disconnect the hoses.

Inspect the inlet screens for:

  • sedimentThe correct troubleshooting steps depend on your Maytag washer model and the condition that triggered the F8E6 code.
  • Before beginning, check your washer’s model number and consult the manufacturer’s instructions.
  • If F8E6 Indicates a Water Hazard or Lid Problem
  • 1. Check the Washer Lid
  • If the washer stopped during a soak cycle or while water was in the tub, make sure the lid is completely closed.
  • Some Maytag washers display F8E6 when the lid remains open too long during certain cycles.
  • 2. Check for Obstructions
  • Inspect the lid opening for clothing or other objects that could prevent the lid from closing properly.
  • Remove any obstructions and close the lid.
  • 3. Inspect the Lid Latch
  • Check the visible lid latch area for damage or debris.
  • Do not attempt to bypass or defeat the lid safety mechanism.
  • 4. Resume or Restart the Cycle
  • Follow the instructions in your washer’s owner’s manual to resume or restart the interrupted cycle.
  • If the error returns despite the lid closing properly, the lid switch, lid lock, or related components may require professional diagnosis.
  • If F8E6 Indicates a Water Supply Problem
  • 1. Disconnect Power and Shut Off Water
  • Unplug the washer and turn off both water supply valves before inspecting or disconnecting hoses.
  • 2. Check the Water Hose Connections
  • Make sure the hot water hose connects to the washer’s hot inlet and the cold water hose connects to the cold inlet.
  • Correct any reversed connections.
  • 3. Verify Water Supply
  • Make sure both supply valves are fully open when the hoses are connected and the washer is ready to operate.
  • 4. Inspect the Inlet Hoses
  • Check for kinked, crushed, leaking, or damaged hoses.
  • Straighten kinked hoses and replace damaged hoses as necessary.
  • 5. Inspect the Inlet Filter Screens
  • With the washer unplugged and the water supply turned off, carefully disconnect the inlet hoses.
  • Inspect the inlet screens for sediment or debris. Follow the manufacturer’s cleaning instructions and avoid damaging or removing the screens.
  • Reconnect the hoses securely and check for leaks.
  • 6. Run a Test Cycle
  • Restore the water supply and electrical power.
  • Run a short cycle to determine whether the error returns.
  • If the problem continues, the water inlet valve or another component may require professional diagnosis.
  • When To Call a Technician
  • Consider contacting a qualified appliance technician if:
  • The F8E6 error repeatedly returns.
  • The washer lid will not lock or close properly.
  • Water continues entering the washer unexpectedly.
  • There is visible water leakage.
  • The problem appears to involve internal wiring, sensors, or electronic controls.
  • Do not operate a washer that is leaking or filling uncontrollably.
  • mineral buildup
  • debris

Clean the screens carefully before reconnecting the hoses.

6. Run a Test CycleThe correct troubleshooting steps depend on your Maytag washer model and the condition that triggered the F8E6 code.

Before beginning, check your washer’s model number and consult the manufacturer’s instructions.

If F8E6 Indicates a Water Hazard or Lid Problem

1. Check the Washer Lid

If the washer stopped during a soak cycle or while water was in the tub, make sure the lid is completely closed.

Some Maytag washers display F8E6 when the lid remains open too long during certain cycles.

2. Check for Obstructions

Inspect the lid opening for clothing or other objects that could prevent the lid from closing properly.

Remove any obstructions and close the lid.

3. Inspect the Lid Latch

Check the visible lid latch area for damage or debris.

Do not attempt to bypass or defeat the lid safety mechanism.

4. Resume or Restart the Cycle

Follow the instructions in your washer’s owner’s manual to resume or restart the interrupted cycle.

If the error returns despite the lid closing properly, the lid sThe correct troubleshooting steps depend on your Maytag washer model and the condition that triggered the F8E6 code.

Before beginning, check your washer’s model number and consult the manufacturer’s instructions.

If F8E6 Indicates a Water Hazard or Lid Problem

1. Check the Washer Lid

If the washer stopped during a soak cycle or while water was in the tub, make sure the lid is completely closed.

Some Maytag washers display F8E6 when the lid remains open too long during certain cycles.

2. Check for Obstructions

Inspect the lid opening for clothing or other objects that could prevent the lid from closing properly.

Remove any obstructions and close the lid.

3. Inspect the Lid Latch

Check the visible lid latch area for damage or debris.

Do not attempt to bypass or defeat the lid safety mechanism.

4. Resume or Restart the Cycle

Follow the instructions in your washer’s owner’s manual to resume or restart the interrupted cycle.

If the error returns despite the lid closing properly, the lid switch, lid lock, or related components may require professional diagnosis.

If F8E6 Indicates a Water Supply Problem

1. Disconnect Power and Shut Off Water

Unplug the washer and turn off both water supply valves before inspecting or disconnecting hoses.

2. Check the Water Hose Connections

Make sure the hot water hose connects to the washer’s hot inlet and the cold water hose connects to the cold inlet.

Correct any reversed connections.

3. Verify Water Supply

Make sure both supply valves are fully open when the hoses are connected and the washer is ready to operate.

4. Inspect the Inlet Hoses

Check for kinked, crushed, leaking, or damaged hoses.

Straighten kinked hoses and replace damaged hoses as necessary.

5. Inspect the Inlet Filter Screens

With the washer unplugged and the water supply turned off, carefully disconnect the inlet hoses.

Inspect the inlet screens for sediment or debris. Follow the manufacturer’s cleaning instructions and avoid damaging or removing the screens.

Reconnect the hoses securely and check for leaks.

6. Run a Test Cycle

Restore the water supply and electrical power.

Run a short cycle to determine whether the error returns.

If the problem continues, the water inlet valve or another component may require professional diagnosis.

When To Call a Technician

Consider contacting a qualified appliance technician if:

  • The F8E6 error repeatedly returns.
  • The washer lid will not lock or close properly.
  • Water continues entering the washer unexpectedly.
  • There is visible water leakage.
  • The problem appears to involve internal wiring, sensors, or electronic controls.

Do not operate a washer that is leaking or filling uncontrollably.

If F8E6 Indicates a Water Supply Problem

1. Disconnect Power and Shut Off Water

Unplug the washer and turn off both water supply valves before inspecting or disconnecting hoses.

2. Check the Water Hose Connections

Make sure the hot water hose connects to the washer’s hot inlet and the cold water hose connects to the cold inlet.

Correct any reversed connections.

3. Verify Water Supply

Make sure both supply valves are fully open when the hoses are connected and the washer is ready to operate.

4. Inspect the Inlet Hoses

Check for kinked, crushed, leaking, or damaged hoses.

Straighten kinked hoses and replace damaged hoses as necessary.

5. Inspect the Inlet Filter Screens

With the washer unplugged and the water supply turned off, carefully disconnect the inlet hoses.

Inspect the inlet screens for sediment or debris. Follow the manufacturer’s cleaning instructions and avoid damaging or removing the screens.

Reconnect the hoses securely and check for leaks.

6. Run a Test Cycle

Restore the water supply and electrical power.

Run a short cycle to determine whether the error returns.

If the problem continues, the water inlet valve or another component may require professional diagnosis.

When To Call a Technician

Consider contacting a qualified appliance technician if:

  • The F8E6 error repeatedly returns.
  • The washer lid will not lock or close properly.
  • Water continues entering the washer unexpectedly.
  • There is visible water leakage.
  • The problem appears to involve internal wiring, sensors, or electronic controls.

Do not operate a washer that is leaking or filling uncontrollably.

Reconnect power and run a short wash cycle to determine whether the error returns.

How To Reset Maytag Washer After F8E6 Error

You can often reset the washer using these steps:

  1. Turn off the washer.
  2. Unplug the washer from power.
  3. Wait approximately 5 minutes.
  4. Plug the washer back in.After correcting the condition that caused the F8E6 error, you may be able to clear the code and restart the washer.
  5. Make sure the washer lid is completely closed.
  6. Correct any water supply or hose connection problems identified during troubleshooting.
  7. Follow the reset or error-clearing procedure in your washer’s owner’s manual.
  8. If the manual recommends a power reset, turn off the washer and disconnect power for the specified period.
  9. Restore power and start an appropriate cycle to check whether the error returns.
  10. Reset procedures vary between Maytag washer models. Disconnecting power may not clear every stored error code.
  11. If F8E6 returns, the underlying problem may still be present.
  12. Start a short wash cycle.

Some Maytag washer models may use slightly different reset procedures.

Frequently Asked Questions

What does F8E6 mean on a Maytag washer?

The F8E6 error code usually indicates a water supply connection issue, often involving reversed hot and cold inlet hoses.

Can reversed water hoses cause the F8E6 error?

Yes. Incorrectly connected inlet hoses are one of the most common causes of the F8E6 error code.

Will unplugging the washer clear the F8E6 error?

Sometimes. However, if the hose installation problem remains, the error will likely return.

Do both water supply hoses need to be connected?

Yes. Many Maytag washer models require both hot and cold water supplies for proper operation.

Is the F8E6 error expensive to repair?What does F8E6 mean on a Maytag washer?

The meaning depends on the model. On some Maytag top-load washers, F8E6 indicates a water hazard condition associated with the lid being open while water is present. On other models, it may indicate a hot water detection or inlet hose connection problem.

Can leaving the washer lid open cause F8E6?

Yes. On certain Maytag top-load washers, leaving the lid open during a soak cycle or while water is present can trigger the F8E6 error.

Can reversed water hoses cause the F8E6 error?

On some models, incorrectly connected hot and cold inlet hoses can contribute to an F8E6 error. Check the model-specific instructions before changing hose connections.

Will unplugging the washer clear the F8E6 error?

A power reset may clear the displayed code on some models, but it will not repair the underlying problem. The error may return if the original condition remains.

Is the F8E6 error expensive to repair?

Not necessarily. If the problem involves an open lid or incorrectly connected water hoses, the correction may be simple. A failed lid lock, water inlet valve, or electronic component could require professional service.

Can I continue using my washer with an F8E6 error?

Do not continue operating the washer if it is leaking, filling unexpectedly, or unable to close or lock its lid properly. Correct the problem before resuming normal operation.

In many cases, the problem can be corrected by properly connecting the water inlet hoses and verifying water flow.

Related Maytag Washer Error Codes